How to Fix a Delta Kitchen Faucet in 12 Easy Steps in 2021
Faucets are a necessary component of our kitchens. They are handy whenever you require water for cleaning, washing utensils, or even washing your hands.
A well-maintained faucet provides a sense of enjoyment in the kitchen. Conversely, a faulty or worn-out faucet can be highly inconvenient.
It may spill water in all directions or even prevent water from escaping. Once you notice that the faucet is not functioning properly, it is necessary to repair it. Therefore, how How to Fix a Delta Kitchen Faucet? Continue reading this article to learn more.
How is a delta kitchen faucet repaired?
To begin, there are several considerations. To begin, you must purchase an authentic replacement part from a reputable retailer. You do not want to spend your money on a non-genuine product that will likely fail to last. Once you’ve obtained genuine parts, proceed as follows:
Cut off the water supply and shut off the valves beneath the sink.
Repairing the faucet while the water is running is nearly impossible. As a result, you will need to turn it completely off.
The next step is to turn off the valves beneath the sink with care. These valves require some attention because they are rarely used and may rust if not properly tightened.
Additionally, they are softer due to their brass construction. This means they can be easily disfigured if force is used to turn them off. While you’re at it, loosen the screws that secure the handle in place.
This is easier to accomplish with an Allen wrench. Remove the handle from the faucet and set it aside to avoid losing any small components.
Increase or decrease the water pressure.
Bear in mind that the water is completely turned off at this point. However, the faucet is an adjustable chrome-dome with a plastic ring for adjusting the water pressure. Adjust the plastic ring to the desired level. This component will also need to be removed to make adjustments.
Remove the disc (plastic) that is always attached to the ball’s upper portion.
As is customary, exercise caution as these items is all delicate. Typically, this rubber is attached to a rubber gasket. The gasket’s purpose is to prevent water from leaking, particularly when the water is opened.
Carefully detach the ball.
Take care not to damage the ball socket when removing the ball. It is attached to one side; therefore, you may wish to avoid damaging that portion. This is because replacing the entire set may prove to be more expensive.
The two pieces of black rubber.
They are visible at the socket’s base. That is the case with the washers. Their job is to keep water from leaking out of the faucet when it is not in use. Bear in mind that even when the faucet is turned off, water remains inside.
Without these washers, water would leak freely. A screwdriver can be used to remove these rubber pieces. Remember to remove the spring as well.
Replace the springs. Carry out the same procedure for the remaining two washers, including the one you removed earlier. Firmly but carefully press it in place until the springs are in place.
Insert a small amount of grease to aid in the lubrication of the faucet. Until the faucet is no longer in use, the grease should act as a lubricant.
Remove its arm by pulling it upward.
Ensure that you rotate it as you pull it out. Be as gentle as possible to avoid breaking any components. Once detached, you’ll notice two enormous black washers. They completely encase the right shaft. Remove and replace these washers as well.
Again, do not forget to apply a small amount of grease to ensure constant smooth rotation. Washers are responsible for preventing water leakage; therefore, they should be well lubricated to function properly.
Replacing the faucet arm and ball socket is necessary.
This is accomplished by firmly pressing down on it while simultaneously rotating it from one side to the other. Again, this is to ensure proper fit. Following that, install another ball socket, paying close attention to the ball’s layout. To begin, ensure that the cylinder is upright. You may need to refer to the delta kitchen faucet repair diagram in order to comprehend the components mentioned here.
Reassemble the components.
Replace the components in the order in which they were removed. Ensure that the plastic ring is adjusted properly. This is intended to make the process of replacing it as simple and painless as possible.
Configure the chrome-dome
At this point, you must ensure that everything fits snugly into its designated location. This may be the most difficult part of the exercise. First, make certain that everything fits properly; otherwise, the faucet will not work properly:
Failure to function – inability to release any water
Continuously run water.
When the chrome-dome is properly fitted, secure it to the entire assembly. Loosen the plastic inset slightly so that the faucet can be turned up and down when fully fitted.
Secure the plastic ring in place to ensure that everything functions properly.
Replacing the faucet handle
Again, you’ll use Allen to reattach it. Take care not to break any components. Before you settle, check to see if any parts remain outside, as this may indicate that you skipped a step while reassembling.
Turn on the water valves and run the water for a test run.
At this point, run the faucet to check for oozes. Consistently increase the volume of water until maximum pressure is reached. Keep a closer eye on the faucet to determine if it is leaking or not. If it is not, then congratulations; you did an excellent job.
Questions That Are Frequently Asked – (FAQ) – How to Fix a Delta Kitchen Faucet
Are you able to repair a delta kitchen faucet?
Yes, these faucets can be repaired. However, a great deal is a contingent upon the extent of the damage. There are some instances where a complete overhaul is preferable to performing repairs. You can perform the repairs yourself or outsource the service.
If the work entails a significant amount of plumbing, I would recommend hiring a qualified individual to complete the task.
The procedure for repairing the faucet is straightforward, and all that is required is an Allen wrench and a screwdriver. Additionally, you may require large joint pliers to assist with the task.
What can wreak havoc on a kitchen faucet?
Numerous factors can contribute to the faucet leaking. Among them are mineral deposits and corrosion in the internal part. Other possible causes include faulty gaskets, washers, and even O-rings.
The majority of these leaks are simple to repair and can be done at home. If you have the proper tools and some basic plumbing knowledge, resolving the issue should be straightforward.
What are the consequences of a leaky faucet?
A room with a leaking faucet is not healthy. Among the consequences are:
- A moist environment.
- The growth of bacteria and algae.
- An increase in water bills.
Additionally, water reduces the useful life of the kitchen and adjacent fixtures. Dripping faucets increase monthly water bills by approximately 10%. This results in increased financial losses.
How much does a kitchen faucet repair cost?
It depends on the extent of the damage. The average price in the United States is between sixty and one hundred and fifty dollars. However, depending on the nature of the issue, you will be able to determine the actual cost. If you purchase all spare parts, the cost will be even higher than when you have them on hand.
How long do cartridges for faucets last?
It is dependent on how the faucet is used. Cartridges adapt easily to their intended use and environment. Regardless of this, it should last between twenty and thirty years. A cartridge typically costs between thirty and forty dollars.
Is it possible to replace the O-rings on my delta faucet?
Yes, they can be replaced when they become worn out. However, after a period of use, their effectiveness begins to wane, and eventually, they begin to leak. It is recommended to replace them whenever they begin to leak.
With these 12 simple steps, hopefully, you can easily repair other faucets, not just Delta faucets.
Hope you enjoyed this article.